Gunsmithing Services

At Cutter Machine Works, we strive to help our customers with all of their firearm needs. Whether you need maintenance, repairs, or modifications, we’ve got you covered! Our gunsmiths can help you diagnose and solve any problems you might have with your firearms. Below is a list of services that we offer.

  • Gunsmithing – $75 per Hour
    • Standard Firearms.
  • Inspection and Diagnosis – $35
    • Thoroughly inspect firearm to determine repairs needed.
  • Test Firing – $10 Plus Ammunition
    • We only use factory ammunition in the box to test fire.
  • Machining – $125 per Hour
    • Milling (RMR Cut $125)
    • Drilling & Tapping ($25 per Hole)
    • Barrel Threading ($125)
  • NFA Items – $125 per Hour
    • Machine Guns
    • SBR | SBS
    • Suppressors

 

*Shop rates are basic rates for services and do not include parts. We will provide a written estimate for authorization of any work performed. Firearms that need to be logged into FFL log book and evaluated by gunsmith will be subject to a $35 minimum billing.

  • Standard Firearm – $40

 

  • NFA Items – $85

 

*Extra charge for excessive rust, dirt and/or removal of any cosmoline type preservatives.

 

  • Pistol Sight Installation
    • Purchased from Cutter Machine Works.¬† – $20
    • Customer provided. – $40
    • 1911 Customer Provided. – $65
  • Pistol Optic Installation
    • Mount, Bore Site on Optic Ready Slide – $35
  • Rifle Optic Mounting
    • Install with Bore Sight. – $35
    • Scope Ring Lapping. – $35
  • Polymer Frame Trigger Kit Installation¬†
    • Trigger Kit Purchased From Cutter Machine Works – $40
    • Customer Provided Trigger Kit – $50
  • Handgun Action Job – $75
    • Engagement Surface Polishing
    • Lighter Springs (if Available)
  • Bolt Action Rifle – $75
    • Tuning/Fitting
    • Safety Function Check
  • AR Rifle – $35
    • Tuning/Fitting
    • Safety Function Check

 

*If the customer provides a trigger kit and it is incomplete, the customer is responsible for paying the cost of additional parts.

  • Small Parts Install
    • Installation of Pearce extension. – $10
    • Change Magazine Release Side. – $10
    • Slide Lock, Extended Mag. – $15
  • Barrel Install – Starts at $75
    • File/Machine
    • Test Fire
  • Revolver Carry Package – $140
    • Detail Clean
    • Trigger Job
    • Sight Alignment
  • Muzzle Device Install – $35
  • Pour Chamber Cast – $75
  • Barrel Threading – $75
  • Bolt Action Rifle Trigger Job – $75
  • AR Rifle Trigger Installation – $35
  • AR Barrel Swap – $75
  • AR Upper Assembly – $65
  • AR Lower Assembly – $65
  • AR-15 | AR-10 Full Tune Up – $150
    • Detail Clean
    • Inspection
    • Small Parts Replacement (including; detent, hammer, trigger springs, gas rings, firing pin)
  • Recoil Pad Install – $140
    • Determine Length of Pull
    • Grind Pad to Proper Fit
  • Drill & Tap Bead – $35
  • Bead Replacement – $15
  • Ruger Single Action, Action Job – $80
    • 17lb Hammer Spring
    • Reduced Power Trigger Return Spring
    • Engagement Surface Polishing
  • Ruger Single Action, Power Custom Free Spin Pawl Install – $100
    • Fitting
    • Timing of Pawl (included)
    • Engagement Surface Polishing
  • Colt & Clone Single Action, Action Job – $100
    • Reduced Power main Spring
    • Reduced Power Wire Type Sear/Bolt Spring
    • Extra Power Base Pin Latch
    • Stainless Ejector Spring
  • Lever Action Rifle, Action Job – $75
    • Engagement Surface Polishing

Additional Information:

*Firearms for gunsmithing must be completely clean, including the inside of action, not just barrel. All dirty firearms will be subject to an additional $40 cleaning fee.

*If you do not see a service listed, please ask. This is not meant to be a comprehensive list of services provided, nor is it a representation of the final bill for services provided.

*Parts are not included unless stated otherwise.

*Once final billing has been issued, if after 15 days item has not been picked up, a $5.00 per day storage fee will be assessed.